㈠ 順槽皮帶輸送機滾筒數量怎麼確定
上海潁盛機械表示：滾筒的數量是由皮帶機的布置方式決定的,但最少數量3個,驅動滾筒1個、改向滾筒1個、增面滾筒一個,拉緊方式根據使用帶寬、輸送長度等選擇,小型皮帶機可選用螺旋拉緊裝置或重錘拉緊裝置,大型皮帶機最好使用重錘拉緊和絞車拉緊。希望你可以參考
㈡ 煤礦里的 運輸順槽 軌道順槽怎麼設計 對皮帶運輸機的影響如何
煤礦井下的運輸順槽一般是指原煤運輸巷道；軌道順槽多為「三巷」布置綜采工作面時做為運輸物料的輔助巷道。多數情況下，皮帶運輸機（膠帶輸送機）多布置在運輸順槽巷道中，此時膠帶輸送機與軌道順槽無直接關系。我理解你所提問題主要是指：「兩巷」布置的綜采工作面，巷道在設計時如何更好的簡化、優化。其一：要結合煤層的地質構造條件，簡化、優化巷道設計之處的支護、掘進方式、成巷型式、掘進周期、掘進工藝等；其二：要重點考慮綜采工作面的採煤工藝、採煤方法、採煤設備的布置型式等：第三：要加強對綜采工作面及周邊的水文、地質等預測預報；第四：充分考慮綜采設備的安裝、運輸等，以綜采設備最大外型尺寸為基礎，合理布置成巷技術參數；第五：兼顧設備的更換、供壓風、供水、排水、各個系統完善所需工程量的大小；第六：需要合理調配采面在收尾結束後，回收設備及工作面收尾條件之間的關系。
㈢ 煤礦回風順槽皮帶機尾錨固深度要求多少
這個一般為一錨桿。你能做到么？
其實就是穩住機尾不上翹移位就可以的。
㈣ 皮帶順槽指的是哪
自動滑扣皮帶內側，凹凸槽的地方
㈤ 順槽皮帶機的「順槽」是什麼意思
簡單地說就是可伸縮儲帶皮帶機；
順槽皮帶機是用於採煤工作面的原煤輸送，開始鋪設最長。隨著採煤工作面回採推進，皮帶機依靠儲帶倉不斷縮短。當這塊煤層采完之後，這台皮帶機也縮至最短，
完成它的本次使命。要麼搬家；要麼升井大修。煤礦上稱其為順槽皮帶機。其實就是專為採煤工作面而設計的可伸縮帶式輸送機。
㈥ 求一份關於皮帶機的英文文獻附帶中文翻譯，字數不能太少
皮帶機是皮帶輸送機的簡稱。
皮帶機是皮帶輸送機的簡稱，皮帶機運用輸送帶的連續或間歇運動來輸送各種輕重不同的物品，既可輸送各種散料，也可輸送各種紙箱、包裝袋等單件重量不大的件貨，用途廣泛。 皮帶機輸送帶的材質有：橡膠、硅膠、PVC、PU等多種材質，除用於普通物料的輸送外，還可滿足耐油、耐腐蝕、防靜電等有特殊要求物料的輸送。採用專用的食品級輸送帶，可滿足食品、制葯、日用化工等行業的要求。 皮帶機結構形式有：槽型皮帶機、平型皮帶機、爬坡皮帶機、轉彎皮帶機等多種形式，輸送帶上還可增設提升擋板、裙邊等附件，能滿足各種工藝要求。輸送機兩側配以工作台、加裝燈架，可作為電子儀表裝配，食品包裝等皮帶機裝配線。 皮帶機驅動方式有：減速電機驅動、電動滾筒驅動。 皮帶機調速方式有：變頻調速、無極變速。 皮帶機架材質有：碳鋼、不銹鋼、鋁型材。 應用范圍：輕工，電子，食品，化工，木業，機械等行業 皮帶機設 備 特點：皮帶機輸送平穩，物料與輸送帶沒有相對運動，能夠避免對輸送物的損壞。噪音較小，適合於工作環境要求比較安靜的場合。結構簡單，便於維護。能耗較小，使用成本低。
皮帶輸送機安全操作規程
1、固定式輸送機應按規定的安裝方法安裝在固定的基礎上。移動式輸送機正式運行前應將輪子用三角木楔住或用制動器剎住。以免工作中發生走動，有多台輸送機平行作業時，機與機之間，機與牆之間應有一米的通道。 2、輸送機使用前須檢查各運轉部分、膠帶搭扣和承載裝置是否正常，防護設備是否齊全。膠帶的張緊度須在啟動前調整到合適的程度。 3、皮帶輸送機應空載啟動。等運轉正常後方可入料。禁止先入料後開車。 4、有數台輸送機串聯運行時，應從卸料端開始，順序起動。全部正常運轉後，方可入料。 5、運行中出現膠帶跑偏現象時，應停車調整，不得勉強使用，以免磨損邊緣和增加負荷。 6、工作環境及被送物料溫度不得高於50℃和低於-10℃。 7、輸送帶上禁止行人或乘人。 8、停車前必須先停止入料，等皮帶上存料卸盡方可停車。 9、輸送機電動機必須絕緣良好。移動式輸送機電纜不要亂拉和拖動。電動機要可靠接地。 10、皮帶打滑時嚴禁用手去拉動皮帶，以免發生事故。
皮帶流水線跑偏故障及解決方法
皮帶輸送機運行時皮帶跑偏是最常見的故障。為解決這類故障重點是要注意安裝的尺寸精度與日常維護保養。跑偏的原因有多種，需根據不同的原因區別處理： 1、調整承載托輥組。2、安裝調心托輥組。3、調整驅動滾筒與改向滾筒位置。4、張緊處的調整。5、雙向運行的皮帶輸送機皮帶跑偏的調整比單向皮帶線跑偏的調整相對要困難許多，在具體調整時應先調整某一個方向，然後調整另外一個方向。
皮帶輸送機的日常維護
1、檢查所有緊固件並確認沒有松動。 2、清潔皮帶並確認皮帶完好，如發現皮帶破損應及時更換。 3、檢查電機減速箱內的潤滑油並確保正常。 4、檢查皮帶張緊度並調整至適當。
皮帶輸送機的國內現狀
我國生產製造的帶式輸送機的品種、類型較多。在「八五」期間，通過國家一條龍「日產萬噸綜采設備」項目的實施，帶式輸送機的技術水平有了很大提高，煤礦井下用大功率、長距離帶式輸送機的關鍵技術研究和新產呂開發都取得了很大的進步。如大傾角長距離帶式輸送機成套設備、高產高效工作面順槽可伸縮帶式輸送機等均填補了國內空白，並對帶式輸送機的減低關鍵技術及其主要元部件進行了理論研究和產品開發，研製成功了多種軟起動和制動裝置以及以PLC為核心的可編程電控裝置，驅動系統採用調速型液力偶合器和行星齒輪減速器。
皮帶機的運輸、貯存
產品在運輸過程中，應符合運輸部門的有關規定，不得與酸、鹼接觸。驅動裝置、電氣設備應避免刮、碰、摔等劇烈的振動和撞擊。在保管期間應採取防雨、防潮措施，貯存時應放置在有遮棚的倉庫內。
Belt conveyor is short for belt conveyors.
Is short for belt conveyor in belt conveyor, belt conveyor using continuous or intermittent motion of the conveyor belt to transport all kinds of different articles, which can transport all kinds of bulk material, can also transport all kinds of cardboard boxes, bags and other little unit weight of goods, a wide range of uses. Belt conveyor belt material: rubber, silicone, PVC, PU, and other materials, except for transportation outside of ordinary materials, meets resistance to oil, also have special requirements such as corrosion-resistant, anti-static materials conveying. Using the dedicated food grade conveyor belt, can meet the requirements of the food, pharmaceutical and chemical instries. Belt conveyor structure: Groove belt machine, flat belt conveyor, belt conveyor and other forms of climbing belt machine, turn, conveyor belt or an additional lift up on the bezel, skirts and other accessories, can meet all technical requirements. Conveyor equipped with table, the installation of lights on both sides, can be used as electronic instrument Assembly, food packaging and other belt conveyor assembly lines. Belt drive: deceleration motors, electric drum drives. Belt speed: variable frequency adjusting speed, multitronic. Belt rack material: carbon steel, stainless steel, aluminium. Range of application: light instry, electronics, food, chemical instry, wood instry, mechanical instry belt machine devices feature: smooth belt conveyor, the material and there is no relative motion of the conveyor, to avoid the damage of transportation. Less noise, ideal for quiet work environment requirements. Simple structure, easy for maintenance. Less energy consumption, low cost.
Safety operation regulations for belt conveyor
1, fixed conveyor should be required for the installation method to install on a fixed basis. Mobile conveyor wheels should be before the official run with triangular wooden wedge, or with a brake check. So that, when there are multiple parallel operation of conveyor, between machine and machine, between the wall and there should be one metre of the channel. 2, shall inspect all machinery before use of conveyor, belt buckle, and host device is normal, protective equipment are complete. Belt tension should be adjusted before starting to an appropriate extent. 3, the belt conveyor unloaded start. After normal operation, such as feed. Prohibit driving after feeding. 4, there are several conveyor-line runs from the discharge end, starting in the order. After all normal operations in order to feed. Belt deviation phenomena appears in the 5, run, stop adjustment shall reluctantly use to avoid edge wear and increase the load. 6, work environment and be sent material shall not be higher than 50 ° c and temperature lower than-10 degrees centigrade. 7, against pedestrian or riding on a conveyor belt. 8, parking must be stopped before feeding, and other uploaded material handling belts do before they can stop. 9, conveyor motor must be well insulated. Mobile conveyor cables don't pull and drag. Reliable earthing of motor. 10, is strictly prohibited to use hand to pull the belt when the belt slipping, so as to avoid accidents.
Misalignment fault belt line and the solutions
A mount of belt conveyer belt deviation is the most common fault. To address such failures key to note that the installation of dimensional precision and day-to-day maintenance. Running a number of reasons, be addressed according to different reasons for difference between: 1, adjusting the carrying idler group. 2, the installation of self-aligning idler group. 3, adjust the position and bend pulley driven drum. 4, tensioning adjustment. 5, bi-directional adjustment of belt conveyor belt running deviation than one-way adjustment of belt line deviation relative to many difficulties, specific adjustment should be adjusted in a certain direction, and then adjust the other direction.
Routine maintenance of belt conveyor
1, check all fasteners and verify that there are no loose. 2, cleaning the belt and make sure that the belt intact, damage should be replaced in a timely manner if a belt is found. 3, check the motor lubricating oil in the gear box and ensure that normal. 4, check of belt tension and adjust to the right.
Domestic status of belt conveyor
Manufacturing in China more varieties, types of belt conveyors. "85" period, through the national one-stop "Nissan tons fully mechanized coal mining equipment" project implementation of belt conveyor technical level has been greatly improved, with high power, long distance belt conveyor of coal mine machine key technology research and new proction of Dr LUI has made great progress in development. As large angle long distance with type conveying machine equipment, and high yield efficient face Shun slot can telescopic with type conveying machine, are filled has domestic blank, and on with type conveying machine of rece key technology and main Yuan part for has theory research and procts development, development success has multiple soft up dynamic and brake device and to PLC for core of can programming electric controlled device, driven system used adjusting speed type liquid couple close device and planet gear deceleration device.
Belt conveyor transportation, storage
In the proct ring transport, should be consistent with the relevant provisions of the transport sector, no contact with acid, alkali. Driving devices, electrical equipment should avoid scraping, touching and wrestling, and other violent vibration and impact. Rain, moisture-proof measures should be taken ring the custody period, should be placed in a shelter when the storage warehouse.